Dorman Key FOB Programming Chevy Explained

Dorman key fob programming is a relatively easy process that can be completed in just a few minutes. The first step is to make sure that the fob is within range of the vehicle.

Looking for a Key FOB Replacement?

Click here > Dorman Key FOB

See these simple steps for programming:

How do you program a Dorman key fob?

If you own Dorman key fobs, follow these simple instructions for easily programmed Dorman FOB:

Please have it in hand at the time of programming.

• 1. Close all vehicle doors.
• 2. Insert the key into the ignition.
• 3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold down until instructed to release in step 9.
• 4. Perform steps 5 through 8 in fairly rapid succession.
• 5. Turn the ignition switch to the ON position (as far as you can go without starting the engine).
• 6. Turn the ignition switch to the OFF position.
• 7. Turn the ignition switch to the ON position.
• 8. Turn the ignition switch to the OFF position.
• 9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
• 10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds.
• 11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).
• 12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode.

All currently programmed and new remotes must be reprogrammed to the vehicle. Easy to program and save time.

Features of Dorman key fobs:

Dorman FOBs are specially designed to give you quick, effortless access to your vehicle.

These auto parts come in a variety of designs, so you can find the perfect one to match your car's key fob.

Most Dorman fobs come with four-button remote control features lock unlock and trunk release buttons.

Some models include panic alarm and valet lock-out features as well.

Plus, they are easy to install and come with a one-year warranty.

Where is the OBD II port located?

It is located under the dash on the driver's side. It is usually located near the foot pedals. The location can vary depending on the make and model of your vehicle.

Click here to read: GMC Yukon Speedometer Problems >

What is a keyless entry remote?

A keyless entry remote is a device that allows you to unlock and start your car without having to use a key. The remote transmits a radio signal to the receiver unit installed in your vehicle, allowing you to unlock doors or start the engine.

When you purchase a replacement remote, it will come with a programming manual instructing you on how to program your remote. In most cases, it is relatively easy and fast.

What is a keyless entry transmitter?

A keyless entry transmitter is a small, battery-powered device that sends a radio signal to your car's keyless entry receiver, which in turn unlocks the doors. The transmitter is also called a fob or remote control.

How do I program my keyless entry transmitter?

It can easily be programmed by following the car's owner's manual. The process usually involves pressing a sequence of buttons on the key fobs and the car's dashboard or door panels.

What are the most common problems with keyless entry transmitters?

The three most common problems are:

1. Battery dies and needs to be replaced.

2. Remote does not work properly and needs to be reprogrammed.

3. Transmitter is lost or stolen.

How can I prevent my keyless entry transmitter from being lost or stolen?

You can keep your keyless entry transmitter from being lost or stolen by taking it with you whenever you leave your vehicle. Consider attaching the transmitter to your sun visor, rearview mirror, or another prominent place in your vehicle.

How do I program a replacement Chevy key fob?

The process of programming a replacement is fairly easy. You will need to have the new and old key fobs as well as the vehicle.

1. Insert the old fob into the ignition and turn it to the ON position. Do not start the engine.

2. Press the LOCK and UNLOCK buttons simultaneously on the new fob three times. The door locks will cycle to indicate that your fob has been programmed.

3. Remove the old fob and insert the new fob into the ignition. Turn it to the ON position. Do not start the engine.

4. Press the LOCK and UNLOCK buttons simultaneously on the new key fob three times. The door locks will cycle to indicate that your fob has been programmed.

You may now start the vehicle.

Can I program my own replacement key fob?

Yes, but it varies depending on the year, make, and model of your vehicle. The programming process is simple with most vehicles.

What is included in the Dorman OE FIX replacement?

Let's look at the three components that are included in the Dorman OE FIX replacement key fob programming kit.

Part 1: Programming Tool

The first component is a key programming tool that only works with the Dorman OE FIX kit.

The programming tool has a plug-in on one end and is ready to be plugged into your car's OBD2 port as soon as you take it out of its package.

The plug-in on the other end is where you will connect your fob to be programmed.

In order for this component to work properly, your car must have been manufactured after 1997 and you will need a working key fob that is already programmed to your car.

Part 2: Key Fob

The second component is a new key fob that will be programmed to your car with the help of the first component, the programming tool.

This fob is unprogrammed and ready to be used as soon as you connect it to the programming tool.

The fob has a battery already installed, so you can start using it as soon as you connect it to the programming tool.

The only thing you will need to do is make sure that your car has been manufactured after 1997 and you will need a working fob that is already programmed to your car.

You don't need both spare keys, just one original fob with a working battery.

Part 3: Key Blank

The third component is a key blank that will be cut to match your car's ignition key.

The key blank will come in a variety of different sizes, so you will need to make sure that you select the size that matches your car's ignition key.

How much does it cost to program a GM key fob?

Programming a GM key fob can be done in under 10 minutes, but the price to get it programmed professionally ranges from $50-$60. If you have a Dorman key fob, you can follow the programming instructions included in the packaging to save on expenses.

How do you program a Chevy factory fob?

There are a few ways to do this, but we'll focus on the most common way.

To start, you'll need the following:

- Two working fobs for your vehicle - A flathead screwdriver - The vehicle's "programming mode" instruction sheet

The first step is to insert the key into the ignition and turn it to the "on" position. Do not start the engine.

Next, use the screwdriver to insert it into the small hole on the side of the key fob. This is the programming or "reset" button.

Press and release this button. The doors will now lock, then unlock to confirm the programming mode has been activated.

Now press any button on the fob. The door locks will lock and unlock again to confirm the programming was successful.

Remove the key from the ignition and test the new key fob by locking and unlocking the doors.

If the programming was unsuccessful, you'll need to start over from the beginning. Make sure you follow the instructions exactly and be patient. It can take a few tries to get it right.

Can a dealership reprogram a key fob?

Yes, a dealership can reprogram a fob. This is a relatively simple process that only requires the dealer to have the programming equipment and a master key with a working fob for the vehicle.

How do you program a Dorman keyless remote?

To program a Dorman, you will need the following items:

• The old and new Dorman keyless remote
• Two 9-volt batteries

Step 1: Open the hood of your car.

Step 2: Locate the two metal tabs on the battery compartment of your remote.

Step 3: With the new remote in hand, hold the battery terminals against the metal tabs on the remote.

Step 4: While holding the terminals against the metal tabs, press and hold the button on the remote for around three seconds.

Step 5: Within that three-second span, push the new remote into the battery compartment of your car.

Step 6: Close the hood of your car.

Step 7: Locate the unlock button on your remote.

Step 8: Press the unlock button on your remote. If your vehicle successfully responds, you will hear a beep.

You have successfully programmed a Dorman keyless remote!

How do I program my keyless remote?

Following supplied simple instructions, you can program your Dorman keyless entry remote for Chevrolet without having to go to a dealership.

Keyless entry remote programming for your Dorman keyless remote is easy. You will need the following items: the keyless remote, two AAA batteries, and the vehicle's keyless entry code.

1. Turn on the ignition of your vehicle and press any button on your remote once; this puts the remote into programming mode.

2. Within three seconds, insert the key into the ignition and turn it to the ON position.

3. Press any button on the second remote and then press a button on your original remote; repeat this step if you have a third remote.

4. Within 30 seconds, turn the ignition off and remove your key; the car is now programmed with all three remotes.

Does my car have remote keyless entry?

The keyless entry system is a very popular option on many late model American-made cars, light trucks, and SUV models. The system allows you to lock and unlock your vehicle's doors and open the trunk without using a key.

The transmitter, or remote, that is used to activate the keyless entry system is usually small enough to fit on a key ring. The transmitter sends a signal to a receiver unit that is installed in your car's doorjamb. The receiver unit activates the door locks when you press a button on the remote and also unlocks the doors when you press the unlock button on the remote.

Original keyless remote not working?

If your original keyless remote is not working, it may be due to a bad battery or a problem with the transmitter.

If the battery in your keyless remote is low, it may not have enough power to work. Couple this with a nearby cell phone that is sending out signals and this may cause your keyless remote to not work well.

If you're positive that the battery in your keyless remote is good, the next step is to check the transmitter. Try replacing the battery in the transmitter and see if that fixes the problem. If it does, the problem is in the original key fob remote.

Key fob working intermittently?

If you are having these problems, your key fob may need to be re-synchronized. The remote control transmitter and receiver in your car communicate with each other through the use of low-powered radio signals. When you press a button on the transmitter, it sends out a signal to the receiver.

The power from the transmitter's battery is used only to send this low-powered signal to the receiver. The transmitter will continue to send this signal as long as the button is pressed until the power from the battery is gone.

When you press a button on the transmitter, the signal is sent to the receiver. If the remote is close to the car, the signal will be stronger and the door will unlock faster. If the remote is far from the car, the signal will be weaker and it will take longer for the door to unlock.

If you are having trouble with your keyless entry system, the first thing you should do is check the battery in the remote. If the battery is good, try moving the remote closer to the car. If the remote is still not working, you may need to have the system re-synchronized.

If you think it is not repairable anymore then a simple replacement would do the job. You can buy a replacement keyless entry remote at most automotive parts stores.

Where to get Dorman's replacement fob?

Dorman manufactures a replacement key fob for the Chevy Cobalt, which is available from most automotive parts stores. The Dorman key fob is a direct replacement for the original key fob and is programmed using the same procedure.

The cost of the Dorman replacement key fob is around $30. This is a fraction of the cost of the original key fob, which can cost upwards of $100.