2004 Chevy Tahoe Key FOB [Expert Guide]

by Christine Chan July 9, 2022

2004 Chevy Tahoe Key FOB

If you are looking for a new key fob for your 2004 Chevy Tahoe, we have just what you need.

Click here for a replacement FOB > Chevy Tahoe Key FOB

How do you program a key fob for a 2004 Chevy Tahoe?

Programming instructions for a 2004 Chevy Tahoe key fob are the same as any other GM vehicle.

Chevy FOB Programming Instructions:

All currently programmed and new remotes must be reprogrammed to the vehicle.

Please have it in hand at the time of programming.

1. Close all vehicle doors.
2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold down until instructed to release in step 9.
4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the engine).
6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds.
11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).
12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode.

How do you program a key fob for a Tahoe?

To program a Tahoe key fob, do the following: First, insert both key fobs into the cups of the Tahoe. Turn on your ignition so that one of the cup holders is blinking. Next, press the unlock button on both key fobs simultaneously. The cup holder will turn off when it is programmed for a second key fob. On keyless entry, remote models for the Tahoe, press both buttons at the same time.

How much is a Chevy key fob replacement?

How much is a Chevy key fob replacement? Replacing your Tahoe key fob can cost anywhere from $40 to more than $200, depending on whether you can do it yourself, and where you take it at. Price quotes from the dealer will likely be higher. To save money, see how to replace a Chevy key fob yourself or get a used replacement from eBay.

How do I program my Chevy key fob?

To program your 2005 Chevrolet Tahoe key fobs: turn off the vehicle and remove all other key fobs from the vehicle; insert the key into the ignition and turn it to RUN (engine off) until you hear a single chime (one second) and then turn the ignition back to OFF; press and hold the power unlock button on the driver's door for between 4-10 seconds; you should hear the chime one time; release the unlock button; press and hold the lock and unlock buttons on the fob together for 5 seconds; you should hear the chime one time; release both buttons. Press the door locks cycle to confirm the key fob is programmed.

How do you program a key fob for a 2009 chevy?

The instructions are based on the three buttons that are located at the top of the key fob. First, turn your vehicle on and remove all other keys from your vehicle. Then, turn it back off and insert the master key into the ignition and leave it in the on position. Turn on your vehicle again and wait until the door locks are unlocked. Within 10 seconds, press the power unlock button three times. The door locks should cycle to show that you have successfully completed the task. If all of this was done correctly, you will now be able to use your new key fob by pressing the power to unlock button once to unlock your doors, and twice to shut them back.

Can I program a replacement key fob?

Yes, you can program a replacement key fob for your Tahoe. First, program the new key by inserting it into one of the cup holders. Then, turn the ignition to 'On'. Next, press and hold down both buttons on each key fob for a few seconds then release them. The doors will lock and unlock to show that the key has been programmed. Then, press both buttons on the new fob to program it. The entered programming mode will last for about one minute and any additional programmed key fob will need to be programmed again. A transmitter programming mode will last for about five minutes. Exit programming mode by pressing and holding both buttons on the key fob. Repeat this process for any additional transmitters to be programmed.

What is the average cost of a Chevy key replacement?

The average cost of a replacement Chevrolet Tahoe key is $220. The actual price varies depending on whether you get it from your dealer or an independent mechanic and how you have it coded. The cost can also vary depending on the type of key you get: mechanical, electronic, or transponder (remote). A used key will likely save you money and is usually available from a salvage auto parts dealer or online auction site like eBay.

Does 2004 Tahoe have a transponder key?

Yes, the 2004 Tahoe has a remote transponder key. The remote control for this vehicle will need to be programmed as well as the ignition lock cylinder. Inside of the remote itself is a computer chip that will need to be reprogrammed by an automotive locksmith or dealer.

How do you program a Chevy Tahoe key fob?

To program a Chevy Tahoe key fob, turn the ignition to "On", then press and hold both the lock and unlock buttons of the original key until you hear it chime twice. Then, press any button on your new key fob to complete the programming process. Remember that you only have 30 seconds after turning on the ignition to complete the programming process or you will need to start over. You should wait a couple of days to make sure that your new key fob works properly before you take it off of your key ring.

How do you program a key fob for a 2003 Chevy Tahoe?

How do I know if my Tahoe has a remote start?

The easiest way to tell if your Tahoe has a remote start option is by looking down at the button on the key. If it is red, then this means that you do not have a remote start. If it is black, then you have a remote start option, but it may need to be enabled by an automotive locksmith or dealership.

Why is the cost of a Chevy Tahoe key replacement so high?

The price of car keys can vary depending on where you get them, but it is usually more expensive to get a new key from the dealership than from a local locksmith. It may also be more expensive to replace your key if you have a transponder chip embedded in it. The price of a replacement key can also vary if you need to get multiple keys made or if your vehicle is equipped with a transponder chip that needs to be reprogrammed and synchronized with your vehicle.

How do you remote start a Tahoe?

Before you can remote start your Tahoe, it has to be running and in the park. The first step is to press the lock button on your key fob once. The second step is to press the unlock button on your key fob three times. When you hear two chirps coming from your vehicle, you know that it is ready to start. If you have not yet enabled your remote start on your vehicle, you will hear one chirp instead of two. The third step is to press the lock button on your key fob once again to begin starting your Tahoe.

Does a 2003 Chevy Tahoe have a remote start?

Yes, the 2003 Chevy Tahoe has a remote start option. However, it may be disabled by the dealership or its owner. You can check whether it is enabled by turning your key to position II and looking for two chirps when you press the unlock button on your fob. If you hear one chirp instead of two, then the remote start needs to be enabled by an automotive locksmith or dealership.