2006 Chevy Silverado Key FOB [Your Go-To Guide]

If you're looking for a 2006 Chevy Silverado Key FOB, then you've come to the right place. Whether you need a replacement Key FOB or just want a spare, we have what you're looking for.

How do you program a key fob for a 2006 Chevy Silverado?

Programming a keyless entry remote for your 2006 Chevrolet Silverado doesn't have to be complicated. In fact, it's much easier than you might think. With a few simple programming instructions, we'll show you how to program your 2006 Chevrolet Silverado keyless entry remote in no time!

Programming Instructions:

All currently programmed and new remotes must be reprogrammed to the vehicle.

Please have it in hand at the time of programming.

1. Close all vehicle doors.

2. Insert the key into the ignition.

3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold down until instructed to release in step 9.

4. Perform steps 5 through 8 in fairly rapid succession.

5. Turn the ignition switch to the ON position (as far as you can go without starting the engine).

6. Turn the ignition switch to the OFF position.

7. Turn the ignition switch to the ON position.

8. Turn the ignition switch to the OFF position.

9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.

10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds.

11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).

12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode.

If for some reason the security light doesn't blink 3 times, try the steps again.

If you still can't get it to work, then take your keyless entry remote to the dealer and they will reprogram it for you.

How much is a key fob for a Chevrolet Silverado 1500?

The Chevrolet Silverado 1500 key fob is available from most auto parts stores for around $35. It is a good idea to have an extra fob for your Chevy Silverado so you can give the extra key to someone else who needs it.

Are all Chevy key fobs the same?

No, the key fob for a 2006 Chevy Silverado is not the same as a fob for a 2009 Chevy Silverado.

The 2006 fob will have a different shape and it may not be as advanced as the 2009 fob.

Does a 2006 Chevy Silverado have a chip in the key?

The short answer is no, there is no chip in the key. The key fob uses a rolling code to communicate with the vehicle.

When you press the lock or unlock button on the fob, it communicates with a receiver in the vehicle. The receiver basically tells the starter and other modules to do or not do something.

The biggest advantage to using a fob is that it's much harder for someone to steal your vehicle. They would need to have the fob as well as access to the vehicle. There are some exceptions, but it's harder than hot-wiring a car for sure.

How do I program my Chevrolet Silverado key fob?

To program your Chevrolet Silverado key fob, you will first need to find the Programming Mode. There are several ways to do this, either by using a printed programming sequence or by using the on-screen Programming Sequence.

• By Printed Sequence: Find a flat surface such as a desk. With the Silverado FOB far away from you, hold down all three of the buttons on your Silverado fob. Take something such as a pen and press it to the flat surface. While holding the Silverado fob over the paper, press all three buttons again. This should be done fairly quickly after the first press of all three buttons. You will see that if your FOB is in Programming Mode, you will see an image on the paper. By using this method, write down the code that appears on the paper in big letters, making sure the Silverado FOB is still in Programming Mode.
• By On-screen Programming Sequence: Press and hold 1 on your Silverado FOB. As you hold down 1, press and release the LOCK button on your Silverado FOB. You will then see a light flash on the dash. This will indicate that you are now in Programming Mode. At this point, you can release both buttons.
• To enter the four-digit code, press the numbers on the keypad of your Silverado FOB. If you make a mistake, you can press the CLEAR button to clear the entered number. Once you have entered the entire code, press and release the LOCK button. If everything was successful, the car horn will beep and your Silverado FOB will blink.

How do you roll down windows with a key fob Silverado?

To roll down the windows on your 2006 Chevrolet Silverado with keyless entry, you will need to have the key fob in your possession and within a few steps, you will be ready to roll.

Hold the keyless entry fob close to your Silverado's door handle. Keeping the fob close to the outside of your Silverado's door handle, press the power lock button.

The windows will start to roll down. Hold the key fob in the same spot and continue to press the power lock button until all of the windows are down. If you want to roll the windows back up, simply reverse the process.

Does the 2006 Chevrolet Silverado have a remote start?

Unfortunately, the 2006 Chevrolet Silverado does not have a remote start. However, many aftermarket remote start systems are available that can be installed in your truck.

These systems allow you to start your truck remotely, and many also include features such as climate control and security.

How do I know if my Chevy has a remote start?

If you have a keyless entry remote, then your Chevy has a remote start. The keyless entry remote will have a small black rubber button in the middle of the key fob. If you have a key, then your Chevy does not have a remote start.

What battery does a Chevy Silverado key fob take?

A Chevy Silverado key fob takes a CR2032 battery.

How do I replace the battery in my Chevy Silverado key?

To replace the battery in your Chevy Silverado key, first find a flat surface to set your key on. You should have a small tool kit that came with your key fob. If not, a small flathead screwdriver should work. Gently pry the case open using the tool. You may need to use a little force, but be careful not to break the case.

Once the case is open, you will see the battery. Remove it and replace it with a CR2032 battery. Make sure the positive and negative terminals are facing the correct direction. Replace the case and screw it back together.

Now your key fob should be working like new!

Or

Grab a replacement Key FOB

What is a remote start kit?

A remote start kit is a system that allows you to start your car from a distance and is compatible with automatic transmission vehicles only. The kit includes a transmitter, which you can use to activate the system from outside the car. The system then sends a signal to the car, which turns on the engine and starts the car.

A remote start kit is a great way to get your car started in the morning without having to go outside in the cold. It's also a great way to cool down your car in the summer before you get in. Remote start kits are relatively easy to install and can be found at most auto parts stores.

How do you program a keyless entry remote for a 2005 Chevy Silverado?

To program a keyless entry remote for a 2005 Chevy Silverado, you will need two valid programmed keys. One of the keys will be used to start the vehicle and the other will be used to program the keyless entry remote.

Programming instructions:

The first step is to turn on the ignition and the hazard lights (or any exterior lights).

Insert one of the valid keys into the accessory switch. Then press and hold both the UNLOCK and the PANIC buttons. After you release those two buttons, press and hold the lock button on your new keyless entry remote for about four seconds.

Release all the buttons and turn off the ignition switch. The hazard lights (or exterior lights) will stay on for about 30 seconds.

Repeat this process for the second remote.

Your new keyless entry remote should now work and your existing remotes should no longer work.

How to exit transmitter programming mode?

To exit transmitter programming mode, turn the ignition off and remove the key from the accessory switch. Then open and close the driver's side door. The hazard lights (or exterior lights) will turn off.

How to exit programming mode?

You can exit the programming mode by inserting a non-programmable key into the ignition. If so, the programming mode is exited automatically when the new key is removed from the ignition. The new key will also need to be programmed.

If the new key cannot be inserted into the ignition, you can also exit the programming mode by turning the ignition from LOCK to RUN 5 times in a row with the non-programmable key.

How do you remote start a Chevy Silverado?

To remote start, a Chevy Silverado all you have to do is press the lock button on your keyless entry system three times within five seconds. This will open the driver's door, so you can press the START button to remote start. If your vehicle is in a garage you may have to open the garage door by hand.

Does a 2003 Chevy Silverado have a remote start?

The 2003 Chevy Silverado does not have a remote start. However, the 2006 Chevy Silverado does have a remote start. If you are looking to add a remote start to your 2003 Chevy Silverado, you can do so by purchasing a remote start kit. There are many different types of remote start kits available, but most come with instructions that will walk you through the installation process.

Can you DIY a car alarm?

Wiring car electronics can be a daunting task, even for the most seasoned of do-it-yourselfers. When it comes to something as important as your car alarm, you want to make sure that it is done correctly. The last thing you need is for your alarm to malfunction on one of the coldest days of winter (or anytime for that matter) and not be able to start your car.

Before you begin, make sure you have all the necessary tools and materials. In addition to the car alarm itself, you will need a wiring diagram, crimp connectors, electrical tape, and wire cutters. It's a good idea to have a digital multimeter with you as well, in case you need to test for voltage or resistance while working on your installation.

Also, make sure that you disconnect the battery before attempting to install a car alarm or add any additional wiring to your car's electrical system.

Read the car alarm's installation instructions thoroughly before beginning to install it in your vehicle. The gist of these instructions should be that you are installing a new alarm, not modifying an existing one. Follow the steps carefully and you should have no problems.

If you are uncomfortable with wiring connections, or if you just want to be on the safe side, take your car to a professional installer.

What is dual vehicle control?

Dual Vehicle control is a wireless system that offers the ability to lock, unlock and trunk release functions on both doors or trunks of your vehicle from the key fob.

The benefits of dual control are convenience and security. Now you do not have to go outside and unlock your vehicle, plus the added convenience of locking both doors or trunks at once.

Features of remote start

Remote start features allow you to start your car from a distance, which can be helpful in a number of situations. For example, if you're running late for an appointment, you can start your car and let it warm up while you're finishing getting ready.

In addition to convenience, remote start can also provide a measure of security. If you're worried about someone breaking into your car, you can activate the alarm and start the car from a distance, which will make it more difficult for a thief to steal your car.

It's also worth noting that remote start can be used to cool down your car in the summer. If you've been out in the sun and your car is heated up, you can start the car and let it cool down before you get in.

Finally, a remote start can be a lifesaver in the winter. If you're stuck in the snow and your car is frozen, you can use remote start to get the car warmed up so you can get on the road.

Always be sure to keep your remote starter fob with you at all times. Do not leave it in the car, as this can be a tempting target for thieves.